SPC5643LF2MLQ1 NXP
Available
SPC5643LF2MLQ1 NXP
• High-performance e200z4d dual core — 32-bit Power Architecture® technology CPU — Core frequency as high as 120 MHz — Dual issue five-stage pipeline core — Variable Length Encoding (VLE) — Memory Management Unit (MMU) — 4 KB instruction cache with error detection code — Signal processing engine (SPE) • Memory available — 1 MB flash memory with ECC — 128 KB on-chip SRAM with ECC — Built-in RWW capabilities for EEPROM emulation • SIL3/ASILD innovative safety concept: LockStep mode and Fail-safe protection — Sphere of replication (SoR) for key components (such as CPU core, eDMA, crossbar switch) — Fault collection and control unit (FCCU) — Redundancy control and checker unit (RCCU) on outputs of the SoR connected to FCCU — Boot-time Built-In Self-Test for Memory (MBIST) and Logic (LBIST) triggered by hardware — Boot-time Built-In Self-Test for ADC and flash memory triggered by software — Replicated safety enhanced watchdog — Replicated junction temperature sensor — Non-maskable interrupt (NMI) — 16-region memory protection unit (MPU) — Clock monitoring units (CMU) — Power management unit (PMU) Qorivva MPC5643L Microcontroller Data Sheet — Cyclic redundancy check (CRC) unit • Decoupled Parallel mode for high-performance use of replicated cores • Nexus Class 3+ interface • Interrupts — Replicated 16-priority controller — Replicated 16-channel eDMA controller • GPIOs individually programmable as input, output or special function • Three 6-channel general-purpose eTimer units • 2 FlexPWM units — Four 16-bit channels per module • Communications interfaces — 2 LINFlexD channels — 3 DSPI channels with automatic chip select generation — 2 FlexCAN interfaces (2.0B Active) with 32 message objects — FlexRay module (V2.1 Rev. A) with 2 channels, 64 message buffers and data rates up to 10 Mbit/s • Two 12-bit analog-to-digital converters (ADCs) — 16 input channels — Programmable cross triggering unit (CTU) to synchronize ADCs conversion with timer and PWM • Sine wave generator (D/A with low pass filter) • On-chip CAN/UART bootstrap loader • Single 3.0 V to 3.6 V voltage supply • Ambient temperature range –40 °C to 125 °C • Junction temperature range –40 °C to 150 °
• High-performance e200z4d dual core — 32-bit Power Architecture® technology CPU — Core frequency as high as 120 MHz — Dual issue five-stage pipeline core — Variable Length Encoding (VLE) — Memory Management Unit (MMU) — 4 KB instruction cache with error detection code — Signal processing engine (SPE) • Memory available — 1 MB flash memory with ECC — 128 KB on-chip SRAM with ECC — Built-in RWW capabilities for EEPROM emulation • SIL3/ASILD innovative safety concept: LockStep mode and Fail-safe protection — Sphere of replication (SoR) for key components (such as CPU core, eDMA, crossbar switch) — Fault collection and control unit (FCCU) — Redundancy control and checker unit (RCCU) on outputs of the SoR connected to FCCU — Boot-time Built-In Self-Test for Memory (MBIST) and Logic (LBIST) triggered by hardware — Boot-time Built-In Self-Test for ADC and flash memory triggered by software — Replicated safety enhanced watchdog — Replicated junction temperature sensor — Non-maskable interrupt (NMI) — 16-region memory protection unit (MPU) — Clock monitoring units (CMU) — Power management unit (PMU) Qorivva MPC5643L Microcontroller Data Sheet — Cyclic redundancy check (CRC) unit • Decoupled Parallel mode for high-performance use of replicated cores • Nexus Class 3+ interface • Interrupts — Replicated 16-priority controller — Replicated 16-channel eDMA controller • GPIOs individually programmable as input, output or special function • Three 6-channel general-purpose eTimer units • 2 FlexPWM units — Four 16-bit channels per module • Communications interfaces — 2 LINFlexD channels — 3 DSPI channels with automatic chip select generation — 2 FlexCAN interfaces (2.0B Active) with 32 message objects — FlexRay module (V2.1 Rev. A) with 2 channels, 64 message buffers and data rates up to 10 Mbit/s • Two 12-bit analog-to-digital converters (ADCs) — 16 input channels — Programmable cross triggering unit (CTU) to synchronize ADCs conversion with timer and PWM • Sine wave generator (D/A with low pass filter) • On-chip CAN/UART bootstrap loader • Single 3.0 V to 3.6 V voltage supply • Ambient temperature range –40 °C to 125 °C • Junction temperature range –40 °C to 150 °
Please make sure your contact information is correct. Your message will be sent directly to the recipient(s) and will not be publicly displayed. We will never distribute or sell your personal information to third parties without your express permission.
